Address：10-1 Xipan Xiangyuan, Luoshe Town, Huishan District, Wuxi City
Categories
AISI/SAE 1045 C45 Round Steel Bar
1045 steel bar is made of a medium carbon, medium tensile strength steel, which has quite good strength, machinability and reasonable weldability under hot-rolled conditions. 1045 round steel can be provided with hot rolling, cold drawing, rough turning or turning and polishing.
AISI 4130 carbon steel bar has excellent strength, toughness and processability. Through normalizing and quenching treatment, the steel can achieve high strength and strength. In addition, the bars have excellent weldability and forgeability.
AISI 4140 steel bar is made of a low alloy steel containing chromium, molybdenum and manganese. It has a high carbon content and a good balance of strength, toughness, wear resistance, impact resistance and heat treatment capabilities.
AISI 4340 carbon steel bar is made of a heat treatable low alloy steel containing chromium, nickel and molybdenum. It has high toughness and high strength under heat treatment conditions.
AISI/SAE 5160 Carbon Steel Bar
5160 steel bar is made of a medium-carbon alloy steel whose specific components include carbon, chromium, manganese, silicon, phosphorus and other elements. In addition, 5160 steel also contains a small amount of chromium for improved hardenability.
AISI/SAE 8620 Carbon Steel Bar
8620 steel bar is made of a kind of low alloy steel mainly composed of iron, carbon, silicon, manganese, phosphorus, sulfur, chromium, nickel and other elements. It has good hardenability and weldability, and can obtain excellent mechanical properties through heat treatment.
EN8/EN9 En Series Round Steel Bar
EN8 is a medium carbon steel with a carbon content of 0.25% to 0.60%. It is often used to manufacture mechanical parts, bearings, gears and other parts. It has high strength and wear resistance and can obtain high hardness and strength after heat treatment.
B500A grade steel is usually used for steel mesh products while B500B grade steel is used for steel bars. B500C steel is rarely required, and it is always worthwhile for structural engineers to check whether B500B grade steel can be used instead of B500C, because B500C usually has a significant cost overhead.
Low Carbon Bright Alkaline Steel Wire
Low-carbon bright alkaline steel wire is a good general-purpose grade and is the most common type in daily life, such as hangers, electrical shelves, store displays and paper clips. It has good bending and flattening performance, is easy to form, and is conducive to welding.
High Carbon Spring Tempering Steel Wire
High carbon steel is used to make spring tempered carbon steel wire. Commonly used grades of spring steel wire do not have a specific chemical name. They are instead specified and manufactured according to performance criteria specific to their primary end use, which is the manufacture of coil springs. These performance standards allow a range of carbon content, but there are other factors, such as tensile strength and bending/winding tests must be met within the specified range.
Epoxy resin coated steel bar is an epoxy resin protective coating prepared on the surface of ordinary steel bar by electrostatic spraying powder high temperature sintering process. The coating has excellent chemical corrosion resistance and does not react with acid and alkali. And the coating has anti-permeability, so it can delay the corrosion medium (such as water, oxygen, chloride, etc.) contact with the steel, so that its corrosion resistance life is greatly extended.
BS4449 Steel Reinforcement Rebar
BS4449 is yet another deformed steel bar standard. It is also differentiated as per European standards. When it comes to manufacturing, the steel bars falling in this standard are also hot rolled, which means that they are also used for general purposes, i.e. in common construction projects.
ASTM A615 Reinforcing Bar Grade 60
ASTM A615 is a deformed steel standard categorized under American standards. These are generally available in diameter between 9.5 mm and 43 mm, and length between 6 m and 12 m. Generally, the steel bars that fall under this standard are under deformed or plain carbon steel.
ASTM A615 Concrete Rebar Grade 40
A615 grade 40 steel adds the most benefit when building materials must hold concrete in compression. Strength is one of the differentiators for these two rebar grades. The minimum tensile strength for A615 grade 40 steel is 70.05 ksi. It has a minimum yield strength of 40 ksi.
ASTM A615 Reinforcement Bar Grade 75
ASTM A615 is a deformed steel standard categorized under American standards. These are generally available in diameter between 9.5 mm and 43 mm, and length between 6 m and 12 m. Generally, the steel bars that fall under this standard are under deformed or plain carbon steel.
TMT means Thermo Mechanical Treatment, which is a thermomechanical process; These TMT steel bars are generally used material in construction for enhanced protection against earthquake and another type of natural disasters. To ensure safety for your structure, TMT steel bars should be resistant to corrosion which helps to obtain a longer life to your structure.
Deformed bar, also known as rebar (short for reinforcing bar), is a steel bar or mesh of steel wires used as tension devices in reinforced concrete and reinforced masonry structures to strengthen and hold the concrete in tension. Deformed bar’s surface is often patterned to form a better bond with the concrete.
ASTM A615 Reinforcement Bar Grade 80
ASTM A615 is a deformed steel standard categorized under American standards. These are generally available in diameter between 9.5 mm and 43 mm, and length between 6 m and 12 m. Generally, the steel bars that fall under this standard are under deformed or plain carbon steel.
WUXI JIUCHUANG STAINLESS STEEL CO.LTD
Tel：+86-18921168065
E-mail：info@jiuchuangsteel.com
Add：10-1 Xipan Xiangyuan, Luoshe Town, Huishan District, Wuxi City
copyright © 2025 WUXI JIUCHUANG STAINLESS STEEL CO.LTD
Business license